Analisa Quenching Air Dan Oli Terhadap Terhadap Nilai Kekerasan Permukaan Baja Karbon Rendah Hardfacing Menggunakan Las Smaw Dengan Polaritas DC- Dan DC+
DOI:
https://doi.org/10.58192/unitech.v3i1.1880Keywords:
Low Carbon Steel, Hardfacing, QuenchingAbstract
When welding, you don't have to connect two metal materials, you can also weld the thickness of the component. Steel is a metal material that can be used in the engineering field to make alloys of other metals so that they can have better material properties than the original metal material. One thing that can be done to increase resistance to wear is to increase the surface hardness of the workpiece. This research carried out an analysis to increase the hardness of the surface of low carbon steel after heat treatment for 60 minutes with variations in quenching media resulting from hardfacing using SMAW welding (shield metal arc welding) with DC+ and DC- polarities. The data analysis technique used in this research is specimen testing. The results obtained later by the research show that DC+ polarity has higher hardness in all specimens tested with a value of 418.66 VHN water quenching, 402.8 VHN oil quenching, 348 VHN non-treatment when compared with DC- polarity with a value of 405, 92 VHN quenching water, 374.02 VHN quenching oil and 323.38 VHN non-treatment. Quenching media with water obtained the highest hardness results with a value of 405.92 VHN.
References
Adiansyahrie. (2010). Melakukan Rutinitas Pengelasan dengan Las Busur Manual. In Kompetensi Keahlian Teknik Pengelasan SMK Negeri 53 Jakarta. Jakarta
Alip, M. 1989. Teori Dan Praktik Las. Penerbit Departemen Pendidikan Dan Kebudayaan.
Amanto, H dan Daryanto. 1999. Ilmu Bahan. Cetakan Pertama. Bumi Aksara..
Bangsawan, I. G. (n.d.). Pengaruh Variasi Temperatur dan Holding Time dengan Media Oli SAE 40 terhadap Struktur Mikro dan Kekerasan Baja Assab 760. Skripsi, UNS
Callister D. William and Retchwisch G. David. 2011. Materials Sciene and Engineering. In S1 Version, Eighth Edition (8th ed., p. 425). Asia: Wiley John & Sons.
D.E. Porter and K.E. Easterling. 1992. Phase Transformations in Metals and Alloys (2nd ed.) London: Chapman & Hall.
Dieter E. George. (1988). Mechanical Metallurgy. In Bacon David (Ed.), Materials Science & Metallurgy (SI Metric). London.
Eddy. 2014. Materi Uji Kekerasan dan Impak. http://eddme27.blogspot.co.id/2014/11/bab-i- pendahuluan-1.html
Jokosisworo, S. 2009. Pengaruh Besar Arus Listrik dengan Menggunakan Elektroda SMAW Terhadap Kekuatan Sambungan Las Butt Joint pada Plat Mild Steel.
Iskandar, M. A. 2013. Analisa Sifat Fisis dan Mekanis Tooth Bucket Excavator Sebelum dan Sesudah Proses Heat Treatment. Tugas Akhir:UMS
Laurence H, Van Vlack. 1995. Ilmu Dan Teknologi Bahan. Edisi Kelima. Erlangga. Jakarta.
Marwanto,A. 2007. Materi Lifeskill Las SMAW. Yogyakarta: Universitas Negeri Yogyakarta
Pramono, A., 2011. Karakterisrik Mekanik Proses Hardening Baja Aisi 1045 Media. Teknik, J., Fakultas, M., Universitas, T., Ageng, S., & Cilegon, T. Quenching Untuk Aplikasi Sprochet Rantai. Jurnal Ilmiah Teknik Mesin,.
Sonawan, H, Suratman, R. 2004. Pengantar Untuk Memahami Pengelasan Logam. Αlfa Beta. Bandung
Supardi, E. 1996. Pengujian Logam. Angkasa. Bandung.
Widharto, S. Teknologi dan Proses Pengelasan. Balai Besar Bahan dan Barang Teknik. Bandung.
Widharto, Sri. 2007. Inspeksi Teknik Buku 6. Pradnya Paramita. Jakarta.
William, Callister D. and David, Retchwisch G.. 2011. Materials Sciene and Engineering. In S1 Version, Eighth Edition (8th ed., p. 425). Asia: Wiley John & Sons.
Wiryosumarto, Harsono, Toshi Okumura. 2008. Teknologi Pengelasan Logam. PT Balai Pustaka (Persero), Jakarta.
